Siding

We're getting the siding up and the tub is in place!

WahoO!

Electical and Plumbing

Well, we've got most of the interior walls completed. There is a hole in the floor where the stairs are supposed to sit. Those have been ordered and should be installed next week sometime. We are now working on electrical and I'm hoping that the plumbing will get started soon as well. Hans is out there today working on getting things going and he is hoping to have the rough electrical done by next week sometime. That means we'll be doing drywall sometime around Nov. 28. Things are looking like they are going to be working out. I have to get things like duct work and furnace details worked out yet but we've ordered a furnace and I'll have to get that out to the house and in place before I can order the ducts, so I can know the measurements. It's exciting and a lot of work at the same time!

Walls inside.

Steve and Cody have started putting up walls on the inside. It's exciting to see some more structure changes. The framing always seems to go so fast because it looks like a lot gets done in a short time.They've done the two small bedrooms and closets on the one side of the house. They are hoping to do the other side and leave room for the tub and shower to go in today.

Windows are in...

We've installed the windows in the house. The only openings that aren't covered are the doors and patio doors. We have one window in the kitchen that is also on back order (it was missing it's brick-mold). The styrofoam is almost all completely on. We've put vapor barrier on all the openings that are not covered because we had a storm warning for tomorrow (although it has been downgraded). We're praying for good weather for the next of the week.

SM Styrofoam

Here's a couple of pictures of how the house is looking with the SM on the outside. We have the basement windows installed now too!

Heating Costs

We're in the process of adding styrofoam insulation to the outside of our house. I've been doing some research and from what I've learned through the Manitoba Hydro web site and others from the states, the R 7.5 SM insulation that we're putting on the house should help reduce heating costs around 30%. We have also installed insulation below the heating pipes in the floor in the basement which will guarantee that the heat from the pipes go into the house instead of into the ground. We should be able to do about 60% of our heating through those pipes using an efficient water heating system that will send hot water through our heating pipes. We will be using a forced air furnace to do the rest of the heating (if it's necessary). According to the quotes that we received from our geothermal estimates (the people who were selling the units and would do the installation) we will be able to heat our house on an average year for about $1,600. This estimate was produced in order to show the savings we would receive by going with their geothermal units instead of a forced air furnace. This amount was based on a house our size, located in an open area with no trees, same amount of windows (double pane), R20 insulation in the walls, and using a low efficient forced air furnace. But since we are surrounded by trees, have installed additional insulation on the outside of the house, using an efficient in floor heating system, and a heat efficient air exchanger we are going to be looking at a lower bill then that. If we use the estimate from Manitoba hydro that we will be saving 30% by using the SM styrofoam on the outside of our house then we are looking at a heating bill of around $1,100 for the year. That's not taking into consideration that we are using a high efficient in floor heating system to do a high percentage of our heating. We have also bought Tri Pane windows in order to keep heat in which will be more efficient then the estimate we received from the Geo Thermal installers. We are also located in an area surrounded by trees and very little wind. This will also be a major help in keeping heat in. I am looking forward to seeing what how efficient our new house is. We would love to install a Geothermal unit next summer. That's what we are planning to do at this time, but we'll see how things look after this winter and what it will cost to install. If you consider that Geothermal costs $15,000 to install and we would be paying 4.6% interest on that money, the cost of geothermal would be:
$500 (operating costs, it was estimated $700 from the quotes we received) + $690 (interest over the year) = $1,190

So we would be paying more to heat with geothermal then with the system we are planning on using now. There is no savings with that and so we can't justify paying an additional $15,000 on a unit that will not save us money which will not pay for itself. If we can install the geothermal system ourselves next year for a much lower cost then it will be worth it because we wouldn't be paying interest on the money used for installing the unit.

Groundpoint (sandpoint) well info...

I had promised a few weeks ago that I'd post some information regarding our well. We are going to use a ground point well that will allow us to get the water from our very high water table. I'm hoping to get it installed soon because I'd like to test the water and make sure that it is safe. If it isn't safe to drink we'll have to bring some drinking water in from another source like bottled water from the CO-OP in Oak Lake or something. I know that there are options for hard water like water softeners and also iron filters and things like that so I think we should be ok as far as that is concerned. I've talked to quite a few people in Oak Lake regarding their ground point wells and many of them have good water. There are a few that have an iron filter and need a softener though. It's nice to know that the water is ready and available though. It would be very a pain to have to haul water for our place with the price of gas etc.

I've done some research online and a bunch of talking with neighbors and friends regarding ground point wells. I'll place a link in the side bar for a great site that I found that provides details on installing the well. We probably will do things a little differently but it gives you an idea of what I'm doing with the pictures and diagrams provided.